Kawasaki Ninja ZX-6R Forum banner

1 - 20 of 32 Posts

·
Registered
Joined
·
2,297 Posts
Discussion Starter #1
has any one upgraded the speedo i was toying with the idea of putting b1 clocks on a j the plugs look the same and i think the looms will the same as it used the same motor apart from a few small changes as afar a i know it dose
 

·
Registered
Joined
·
11,637 Posts
Can be done.. Think there is a diy
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #3
thats cool i like the look of the newer clocks
 

·
Registered
Joined
·
4,692 Posts
You'll have to rewire the plug, but that's it. There's a light that'll stay on anytime the bike's running too (down on the lower right i believe). Nothing will be wrong with your bike, so disregard the light. Most guys remove it or electric tape over it.
 

·
Registered
Joined
·
794 Posts
i rewired my plug to run the 03-04 636 gauges and it works fairly well. if you do the 05-06 ones youll need a speedo healer
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #6
Is there a how 2 anywhere and what wire needs to be changed and I think I'll go for the 03-04 clocks
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #8
that looks like a lot of fun could be a job for when its cold and wet
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #9
Iv just been looking at some 07 clocks on eBay dose any one know if they can be fitted to a j1
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #10
Right I'm doing it the new clocks will be here in a few days so a job for the weekend
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #11
right they are on and boy was it a lot easyer than i thought it was going to be ill get some pics up in a bit once im home would any one know what engine temp sender i would need for the temp guage to work??
 

·
Registered
Joined
·
794 Posts
not sure may have to go with a 07 temp sensor, i had to go with an 03 one to get my 03/04 gauges to work. just check what output range they are and compare them to the 07 gauges
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #13
the old clocks as they used to look



and now the new ones look good i think lol




note the really good milage i now have
 

·
Registered
Joined
·
2,558 Posts
They look really good!

Hmmm....Could the same thing be done with an F3?
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #15
i shouldnt see y not just have to figure out what each wier dose on ur loom
 

·
Registered
Joined
·
2,558 Posts
I've got the Haynes for mine....I think I'll be looking into this a bit closer!

Did your clocks have the speedo cable go into the lower left side?

Where does it go now on the new clocks?

Dammit....I really need to stop buying things for my bike :lol:
 

·
Registered
Joined
·
2,297 Posts
Discussion Starter #17
ahh if u have a mechanicel speedo it wont work it needs to have the sender from by the front sprocket as its all electrical sorry to put a downer on thing the other option is get a j1 engine in there
 

·
Registered
Joined
·
2,558 Posts
Ahhh phuck it!

:lol:

Oh well, that's some money saved then!
 
1 - 20 of 32 Posts
Top