Kawasaki Ninja ZX-6R Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 75 Results
  1. Mechanical and Technical
    I seem to be having a very specific problem that others have also had, but I found no good answers for it. When driving at speeds over 25-30 mph, It is impossible to shift from 3rd gear down into 2nd gear without getting into neutral. It goes into neutral when clicking down from 3rd gear and I...
  2. The ZX6R
    I ordered https://www.amazon.com/FTRT-Kawasaki-ZX6R-ZX10R-Z750R/dp/B07FCJXTG3 for my track bike and it turns out they are only ZX6R 07-17 compatible and I've got a 2019. Brake lever fitted fine (has done 114 track miles) but Clutch not so much (totally different mounting between ZX6R 7-17 and...
  3. Mechanical and Technical
    Hey All, I'm running a 2016 ZX-6R that I picked up used with a little under 8K miles on it a few months ago. Was running fine for the most part, except that the past few weeks the clutch cable(pull?) seems to be getting looser. As a result, it has gotten harder to downshift or even fully engage...
  4. The Build Thread
    I am going to be rebuilding my clutch soon by replacing the friction plates, steel plates, and springs. I am going to be getting Ebc springs so that’s taken care of but I am wondering how many friction plates and steel plates I need to replace as well as anything else I might need (will be...
  5. The ZX6R
    So i think i burned my clutch out. Im the third owner (currently 36k) and this thing has had a bunch of weird stuff done to it. Was running well though (did tune up when purchased, rode approx 1k) and i was with a buddy, trying to show off. did a couple burnouts and instant charma..tried to pull...
  6. The ZX6R
    Hey peoples, unfortunately recently I was in an accident where I dropped my bike on it’s left side. The result of the accident was a dent to tank, and some scratches and cracks to plastics. most importantly my gear shift linkage snapped off the rear set foot peg assembly. initially I have...
  7. The ZX6R
    I just picked up a 2001 zx6r that had been sitting for 2 years, got it running but while riding it doesn't wanna go past 7k rpm and seems to be bogging but when I'm not in gear I can redline it. I replaced the clutch plates and friction plates now it revs to 8k while riding. Not sure where to go...
  8. Mechanical and Technical
    Hi! I have a 2001 ZX-6R (J2) and my clutch seems to slip during hard acceleration typically in 1th and 2nd gear. I have changed the friction plates because a friend told me that could be the issue. Unfortunately the issue remains. I also checked the steel plates which looked a little burnt but...
  9. Mechanical and Technical
    Been having an issue with either my tire spinning or clutch slipping, cant figure out which one. Tires were relatively warmed up (michelin power 5's), and this happens under hard acceleration usually starting in first gear. A 2006 zx6r with -1 +2. Video linked, any help is appreciated...
  10. The ZX6R
    Hi, Was riding the bike yesterday with no issues when it started moving in to neutral from third gear during a downshift. Downshifted from 3rd and it went in to neutral, shifter was stuck down and had to let go of the clutch then re-clutch and force the bike in to gear. Forcing the shifter up...
  11. Mechanical and Technical
    Hey guys. I'm having an issue with my 02 zx6r. The engine is cutting off when the clutch is released. The bike will start fine, respond well when throttle is given, and idle fine. When I put the bike in gear, the engine will run for as long as I hold the clutch, but when the clutch is...
  12. Mechanical and Technical
    It seems to be slipping in 3rd gear, 1st and second are good but 3rd... theres something wrong haha. If I skip from 2nd to 4th and so on it's fine. But 3rd has no power and Im not sure if it's clutch or gear box problem. Sorry if this isn't detailed enough. But thanks if anyone has advice.
  13. The ZX6R
    Hello ! I have a ZX6R 2007 , and problem i am having is the clutch freeplay is constantly changing, when its standing still not runnings, its all fine, but when engine is running, properly adjusted clutch cable, its all good , but then out of nowhere, it has a lot of slack into it. Then after a...
  14. Mechanical and Technical
    I have two 2005-06 Kawasaki Ninja ZX6R 636s. One is fully race-built, but came with normal weight springs. The levers are CRG adjustable foldable levers.. The other is street legal, but I rebuilt it from the ground up after 2 years of owning it. With the rebuild came the EBC racing clutch kit...
  15. Mechanical and Technical
    Hey all, New here but I have a quick question. I recently switched my '19 zx6r to gp shifting and when I tried to use the quickshifter (going downwards now), I noticed it got stuck and then eventually shifted if i tried a little harder. However, I realized that the '19 zx6r quickshifter is...
  16. Stunting
    Hey guys, I'm new to the forum. I just picked up a 2013 ZX6R and i'm looking to turn it into a street legal stunt bike. Just wondering if anyone has any suggestions for which stunt clutch to get? I'm currently looking at either an RSC or 1FNGR. Thanks, Tim
  17. Member Classifieds
    For sale two sets of SBS dual carbon brake pads and clutch cover gasket for 2013 and up zx6r $85 shipped
  18. Mechanical and Technical
    Hey guys, I just picked up a 95 zx6r and am in need of a new or used clutch push rod. ROD, CLUTCH Part Number: 46102-1371 Previous owner lost it.. its the small pin that goes in the middle of all the clutch discs. I’m struggling to find any info on if a rod from a newer bike may work. It’s an...
  19. Mechanical and Technical
    hey guys, i purchased my 1999 zx6r last week. this bike has been abused very bad and the previous owner had no time to work on it. before anyone asks, i bought this bike because i want to learn how to work on bikes and this was the perfect opportunity. i have been slowly diagnosing problems and...
  20. Mechanical and Technical
    Hi all, First off, I would like to thank ZX6R.com for being here and giving me the opportunity to join up! I own a 2005 636 since 2k8 with 11.5k miles on it. My girl, Sookie, now has just over 48k. The problem being experienced is that her clutch is grabbing high. My first thought was clutch...
1-20 of 75 Results
Top